How Often Should I Service My BCD?

How often should you service dive regulator?

The correct functioning of the regulator is dependent upon proper maintenance.

Therefore, your regulator should be submitted to a XXXXXXXXXX authorized service centre for inspection at least once a year.

It is also recommended that the first stage valve be replaced every two years or every 200 diving hours..

How much does a scuba tank refill cost?

Gas Fills32% NITROX FILLS – 12 LITRE OR LESSRRPFill between 0 and 200 BAR$20Fill between 30 and 200 BAR$18Fill between 30 and 300 bar$30

What is the best BCD?

Best Scuba BCDs of 2020Cressi Start. BEST FOR: BUDGET.Zeagle Scout. BEST FOR: COMFORT.Aqua Lung Wave. BEST FOR: BEGINNERS.Zeagle Express Tech. BEST FOR: WARM WATER.Oceanic Oceanpro. BEST FOR: DAILY USE.Scubapro GO. BEST FOR: TRAVEL.Hollis HD 200. BEST FOR: ADVANCED SPORT DIVERS.APEKS Black Ice. BEST FOR: COLD WATER DIVERS.More items…•

How do you dry the inside of a BCD?

Inflate the BCD (Buoyancy Control Device) and empty out any water from the bladder. Generally turn it over so the elephant’s trunk is lowest and press the deflate button. Then hang it up over the bath / shower. Most of the BCD materials aren’t that porous, so there’s not that much water caught up in the material.

How do you clean a first stage regulator?

Rinsing your regulator with fresh (warm) water. … Rinse it within a few hours after the dive. … Dry the dust cap before putting it on the first stage. … Do NOT soak the first stage. … Soak some regulator parts for a while. … Wiggle the second stages underwater. … Do NOT press the purge button. … Clean the mouthpieces properly.More items…

What is the difference between yoke and din?

The yoke is a clamp-type mounting, which is placed over the tank valve and then tightened into place. The DIN is a threaded valve, wherein you screw the regulator into the tank valve. On the yoke valve, the main O-ring that seals the tank valve to the regulator first stage is placed on the tank valve.

How do you clean a regulator?

Rinsing your Regulator With a Hose Using a hose for a fresh-water rinse is the first method of cleaning our gear. The scuba unit should still be fully assembled and turned on. First, gently spray the unit to remove any dirt or salt residue (Photo 1). Now individually rinse each part of the regulator.

How much does it cost to service a BCD?

IMPORTANT NOTICE – If your tank or valve is older than 15 years Abyss Scuba Diving will NOT hydro test or fill your Tank OR Valve….Dive Gear Servicing Price List.BCs – includes labour & service kitsRRPBC Service$50Powerline (standard over the shoulder) inflator service kit$65Power Deflation System$751 more row

How do you clean a BCD?

Fresh, clean water is all that is normally needed to clean your BCD, though you may use a mild liquid detergent diluted in fresh water, or a commercial BCD conditioner like McNett BC Life Cleaner and Conditioner for BCDs, in the final rinse to inhibit the growth of mold or mildew and to keep the BCD fresh and odour- …

Can you dive without a BCD?

Divers have been known to use their drysuits as a primary buoyancy device. … Sport and technical divers should never consider diving without a BCD that has an air cell. A BCD is just like any other ‘tool for the job’ in that you should pick the right BCD for the dive you are planning.

How much lift does a BCD need?

It said something to the effect that one should choose a BCD with 10 or so pounds more lift than the total weight worn. As an example it said a diver who wears 30 pounds of weight should have BCD with at least 40 pounds of lift.

How long should a BCD last?

approx 8 yearsSPG: Typical lifespan of two years (1000 dives) before failure. BCD: With routine maintenance and proper care, I find they last approx 8 years (4000 dives) before replacement becomes preferable to repair. Minimalist backplate/wing style BCDs tend to be far more rugged and long-lasting.